1.1 Appearance: lens circuit board without deformation, clean no dirt, no false welding, solder spot, bright, each mark symbol should be clearly visible, the focal length is clear;
1.2 Structure size: 38mm×55mm , PCB board thickness: 1.6 mm;
1.2.1 Circuit board dimensions should be 38mmX35mm surface device height should be less than 4mm.
1.2.2 Slot with PCB aperture of 2.5*3.3mm (four positioning holes);
1.2.3 The height of the lens from the front of the PCB is 22mm±0.2mm;
1.3 Environmental and electrical parameters;
1.3.1 Temperature: -20℃~ +60℃,
1.3.2 Working voltage: DC-12V (9-18V);
1.3.3 Working current: ≤30mA;
1.3.4 Video interface output impedance force should be 75Ω(1Vp-p, 75Ω);
1.3.5 The standard color palette shall be distinguished on the camera under conditions of illumination greater than 0.2LUX, and the color of the monitor image shall be consistent with the color palette.
1.3.6 The horizontal resolution of the camera is 600TVL (collectively referred to in the market).
2.1 The detection camera should meet the requirements of Article 1.1;
2.2 Use vernier calipers to measure the shape, positioning hole, lens height and others of the camera, which should meet the requirements of 1.2.1 in 1.2;
2.3 The camera is connected to the display module and the display for detection, and the image shall not be distorted and other image distortion;
2.4 When the camera is working, the oscilloscope is used to measure the video signal video output amplitude test: 0.8~1.2VP-P/75Ω;
2.5Connect the cable between the camera and the display, place the standard color card 0.8 meters in front of the camera, and the image on the observation monitor should be consistent with the real scene;
2.6High and low temperature test: the temperature is 60℃ for 12h, the power is added to work normally, the temperature is negative 20℃ for 12h, the power test can work normally;
2.7 Camera lens 3.6mm lens horizontal Angle of view 51°, no dark Angle around the image;
2.8 Stability test, continuous aging for 24 hours, there should be no failure;
2.9 camera minimum illuminance test, camera minimum illuminance 0.01LUX.(no LED light).
3.1 Vernier caliper with an accuracy of ±0.02㎜.
3.2 24 color standard color card, gray comprehensive test chart.
3.3 regulated power supply for display module camera, 14 inch color monitor.
| Model | SKY-DL-2389 |
| Camera element | 1/4 sensor |
| Effective pixels | 640 x 480 |
| Image format | PAL |
| Sync mode | Built-in sync |
| Horizontal resolution | 600TVL (market collectively) |
| Signal to noise ratio | >40dB |
| Minimum illumination | 0.01UX |
| Backlight compensation | Automatic |
| Electronic shutter | 1/50Sec-12.5uSec |
| White balance | Automatic |
| Gamma Correction | > 0.45 |
| Video output | 1.0Vp-p75ohm |
| Power required | 12V (9-18V) |
| Current consumption | ≤40mA |
| Lens | 3.6mm 650 |
| Lens horizontal Angle | 48 degrees |
| Optical format | 1/4 |
| Pixel array | 1280 (H) ×720 (V) |
| Image resolution | AHD720P CVBS 1000TVL |
| Video format | PAL/NTSC |
| Video signal | AHD/CVBS |
| Lens focal length | optional |
| Horizontal Angle | optional |
| Lens height | optional |
| Working voltage | DC 9-15V |
| The overall dimension | 38×54 |
| Fill light optional with LED light | |
| Analog 600 wire |